Pincer Placard™

$69.90


The Agilite Pincer Placard™ is a hook-backed elastic placard that holds three 5.56 magazines. Its revolutionary Patent Pending funneled magwell design allows you to grab or re-index a magazine with just one hand while still maintaining rock solid retention so your mags never fall out.

Elastic mag pouches are popular due to their easy access and low profile. However, they all have 1 of 2 flaws:

Either they’re too closed so it’s nearly impossible to re-insert a mag with 1 hand.
Or, they are too loose so you can re-insert a mag but you have to worry about it falling out due to unreliable retention.

The Pincer Placard™ solves both of these problems and gives you the best of all worlds.
The Patent Pending funneled magwells guide your mags into the pouches allowing you to re-insert a mag, snag-free, with just one hand. Despite this capability, the Pincer pouches still retain the magazines tightly so you never have to worry about losing them.

The Pincer Placard™ is supplied with both MOLLE placard buckles and G hooks as standard and has a built-in height adjust capability so it can fit not only Agilite plate carriers but any placard-compatible plate carrier and get a perfect fit instantly. It also has side laser cut loops for attachment to common chest rig systems.

The base of the Pincer placard is made from laser-cut Mil-Spec Squadron material that allows for water drainage but covers the ends of your mags to protect them from dust, dirt and abrasion that can cause weapon malfunctions.

The Polymer magwells give elastic pouches long-term reliable retention and superior durability where they normally fall apart.

Although not required, the Placard also has a loop interior so you can add Agilite Jump Retention tabs if your unit’s regulations require for parachuting, rotary or maritime ops or if you just feel like adding an extra layer of retention. They incorporate Agilite’s proprietary AG™ polymer pull tab technology so even when applied, they give you unhindered, one-handed access to your magazines.

Whether you’re defending your country at the tip of the spear or defending your family, The pincer placard will give you an edge.

Fits three 5.56 magazines
• Hook backed mag pouch for Placard Capable Plate Carriers
• Patent-Pending funneled magwells guide the mag to the optimal insertion point for snag-free, speed re-indexing of mags
• Polymer magwells give elastic pouches long-term reliable retention and superior durability
• Attaches to any Agilite or other placard-capable plate carrier or pack in seconds
• Built-in height adjustment capability for perfect plate carrier positioning
• Both G Hook and Placard Buckle compatible (both provided with product)
• Allows for silent magazine draw or re-insertion
• Designed, tested and battle-proven in Israel

• Fits three 5.56 magazines
• Weight: 5.6oz (161g)
• Dimenetions: 25cm * 9cm (9.8" x 3.5")
• Patent Pending durable polymer magwells
• Proprietary mil-spec G Hooks
• Includes mil-spec Polymer MOLLE Placard buckles
• Laser-cut Squadron mil-spec laminate fabric

The Pincer Placard will fit ANY placard-capable plate carrier and is provided with both G-Hooks and MOLLE placard buckles.

The Pincer placard is built to fit three 5.56 magazines and may also fit similar sized or smaller items.

Hook and loop chest pannel dimenetions: 25cm * 9cm (9.8" x 3.5")

Q: Will this fit my Plate Carrier
A: The Pincer Placard Attaches to any Agilite or other placard-capable plate carrier or pack in seconds

Q:What caliber Magazines will the Pincer Placard Fit?
A: The Pincer Placard™ only fits 5.56, AR-15 Style Magazines

Q:Does this pouch come in singles?
A: at the moment the pincer placard is only available as a triple mag pouch

Q:Do I Need Jump Retention Tabs for the Pincer Placard?

A:Only if your unit’s regulations require them for parachuting, rotary or maritime ops or if you just want an extra layer of retention. If you're putting other items in the pouch besides 5.56 mags, you may want to use them for additional retnetion.

Q: Will items other than 5.56 magazines fit in the pincer placard?
A:Yes, it is intended for 5.56 magazines but other similar sizes items may also fit eg flashlights. For other items you may want to add Agilite Jump Retention tabs

• Free US Shipping on this product (and rest of your order)
Customers Return Policy - If you are not 100% satisfied with your purchase, you can return the product and get a full refund. You can return a product for up to 30 days from the date you received it. Any product you return must be in the same condition you received it in. For any further questions and for info on returns from outside the U.S please contact us at customercare@agilitegear.com

To purchase this product via GSA click here   

Agilite products can be purchased through numerous US and other Government procurement contract vehicles including GSA, TLS, Dod Fedmall and others:
 
  • Prime Vendor purchases available through TSSI- Find your relevant branch rep here (e.g. Army/Navy/AF/USMC/Law Enforcement)  
    • GSA Contract:  GS-07F-016DA
    • DLA Tailor Logistic Support Program (TLS): Contract # SPE8EJ-19-D-0001 OR REQUEST A QUOTE HERE
    • DoD FedMall 
    • Our products come in USA Made or Berry Compliant Versions for contracting and procurement compliance.
    • For all government sales questions or inquiries contact us at govsales@agilitegear.com or call  (+1) (870)-298-4152
If your organization is already set up with one of our distributors, feel free to reach out to them for a quote: US Dealers

Color
Multicam
Ranger Green
Black


The Agilite Pincer Placard™ is a hook-backed elastic placard that holds three 5.56 magazines. Its revolutionary Patent Pending funneled magwell design allows you to grab or re-index a magazine with just one hand while still maintaining rock solid retention so your mags never fall out.

Elastic mag pouches are popular due to their easy access and low profile. However, they all have 1 of 2 flaws:

Either they’re too closed so it’s nearly impossible to re-insert a mag with 1 hand.
Or, they are too loose so you can re-insert a mag but you have to worry about it falling out due to unreliable retention.

The Pincer Placard™ solves both of these problems and gives you the best of all worlds.
The Patent Pending funneled magwells guide your mags into the pouches allowing you to re-insert a mag, snag-free, with just one hand. Despite this capability, the Pincer pouches still retain the magazines tightly so you never have to worry about losing them.

The Pincer Placard™ is supplied with both MOLLE placard buckles and G hooks as standard and has a built-in height adjust capability so it can fit not only Agilite plate carriers but any placard-compatible plate carrier and get a perfect fit instantly. It also has side laser cut loops for attachment to common chest rig systems.

The base of the Pincer placard is made from laser-cut Mil-Spec Squadron material that allows for water drainage but covers the ends of your mags to protect them from dust, dirt and abrasion that can cause weapon malfunctions.

The Polymer magwells give elastic pouches long-term reliable retention and superior durability where they normally fall apart.

Although not required, the Placard also has a loop interior so you can add Agilite Jump Retention tabs if your unit’s regulations require for parachuting, rotary or maritime ops or if you just feel like adding an extra layer of retention. They incorporate Agilite’s proprietary AG™ polymer pull tab technology so even when applied, they give you unhindered, one-handed access to your magazines.

Whether you’re defending your country at the tip of the spear or defending your family, The pincer placard will give you an edge.

Fits three 5.56 magazines
• Hook backed mag pouch for Placard Capable Plate Carriers
• Patent-Pending funneled magwells guide the mag to the optimal insertion point for snag-free, speed re-indexing of mags
• Polymer magwells give elastic pouches long-term reliable retention and superior durability
• Attaches to any Agilite or other placard-capable plate carrier or pack in seconds
• Built-in height adjustment capability for perfect plate carrier positioning
• Both G Hook and Placard Buckle compatible (both provided with product)
• Allows for silent magazine draw or re-insertion
• Designed, tested and battle-proven in Israel

• Fits three 5.56 magazines
• Weight: 5.6oz (161g)
• Dimenetions: 25cm * 9cm (9.8" x 3.5")
• Patent Pending durable polymer magwells
• Proprietary mil-spec G Hooks
• Includes mil-spec Polymer MOLLE Placard buckles
• Laser-cut Squadron mil-spec laminate fabric

The Pincer Placard will fit ANY placard-capable plate carrier and is provided with both G-Hooks and MOLLE placard buckles.

The Pincer placard is built to fit three 5.56 magazines and may also fit similar sized or smaller items.

Hook and loop chest pannel dimenetions: 25cm * 9cm (9.8" x 3.5")

Q: Will this fit my Plate Carrier
A: The Pincer Placard Attaches to any Agilite or other placard-capable plate carrier or pack in seconds

Q:What caliber Magazines will the Pincer Placard Fit?
A: The Pincer Placard™ only fits 5.56, AR-15 Style Magazines

Q:Does this pouch come in singles?
A: at the moment the pincer placard is only available as a triple mag pouch

Q:Do I Need Jump Retention Tabs for the Pincer Placard?

A:Only if your unit’s regulations require them for parachuting, rotary or maritime ops or if you just want an extra layer of retention. If you're putting other items in the pouch besides 5.56 mags, you may want to use them for additional retnetion.

Q: Will items other than 5.56 magazines fit in the pincer placard?
A:Yes, it is intended for 5.56 magazines but other similar sizes items may also fit eg flashlights. For other items you may want to add Agilite Jump Retention tabs

• Free US Shipping on this product (and rest of your order)
Customers Return Policy - If you are not 100% satisfied with your purchase, you can return the product and get a full refund. You can return a product for up to 30 days from the date you received it. Any product you return must be in the same condition you received it in. For any further questions and for info on returns from outside the U.S please contact us at customercare@agilitegear.com

To purchase this product via GSA click here   

Agilite products can be purchased through numerous US and other Government procurement contract vehicles including GSA, TLS, Dod Fedmall and others:
 
  • Prime Vendor purchases available through TSSI- Find your relevant branch rep here (e.g. Army/Navy/AF/USMC/Law Enforcement)  
    • GSA Contract:  GS-07F-016DA
    • DLA Tailor Logistic Support Program (TLS): Contract # SPE8EJ-19-D-0001 OR REQUEST A QUOTE HERE
    • DoD FedMall 
    • Our products come in USA Made or Berry Compliant Versions for contracting and procurement compliance.
    • For all government sales questions or inquiries contact us at govsales@agilitegear.com or call  (+1) (870)-298-4152
If your organization is already set up with one of our distributors, feel free to reach out to them for a quote: US Dealers


Pincer Placard™ Downrange

Customer Reviews

Based on 222 reviews
96%
(213)
4%
(8)
0%
(1)
0%
(0)
0%
(0)
M
Maksim

Pincer Placard™

F
Fan Lo
Pincer Placard is awesome

Pincer Placard secured your Mag so well that you will never need to worry about mags fall out while you sprinting or jumping. And it is really easy to replace too and it allows you to complete changing mag in one hand.

R
Rayne
Agilite nails it, again.

Everything produced by this company is quality and at a reasonable price. The Pincer Placard has instantly replaced all the other placards I own. Retention is perfect and draws like butter. Pull the trigger if you're on the fence.

K
Kevin H
Pincer Placard

Once my magazines are inserted I don't have to worry about them, even if I'm on the ground firing from the prone position. Glad I bought this addition for my K19.

W
WILLIAM MEBANE
Great placard

Really solid design.

Youtube Reviews